In the Trenches: Using RIS to Deploy Windows 2000 Server
Download the authoritative guide: Data Center Guide: Optimizing Your Data Center Strategy
Download the authoritative guide: Cloud Computing: Using the Cloud for Competitive AdvantageThomas Shinder
If you ask the average Windows 2000 "Joe" what operating systems you can install using the Remote Installation Service (RIS), he'll tell you authoritatively "You can only install Windows 2000 Professional using RIS". And if you were looking for the official party line, he'd be right. However, in the world of Windows 2000, it's the exceptions that are the rule.If you ask the average Windows 2000 'Joe' what operating systems you can install using the Remote Installation Service (RIS), hell tell you authoritatively 'You can only install Windows 2000 Professional using RIS'. And if you were looking for the official party line, hed be right. However, in the world of Windows 2000, its the exceptions that are the rule.
Yes, Dorothy! Deploy Windows 2000 Using RIS
The fact is that you can deploy Windows 2000 Server using RIS. We encountered such a situation not too long ago where we needed to install 6 Windows 2000 Servers. Since I had some extra time to do some experimenting, I checked TechNet for any information that might allow me to use RIS and give me another opportunity to complain about the service.
Well, I didn't get another opportunity to complain, but I did find some information on how to use RIS to deploy Windows 2000 Server. The caveat here is that Microsoft does not support this, and if anything bad happens, the fingers are all going to point to you. Although Microsoft does not explicitly state what types of problems you might encounter by deploying Windows 2000 Server using RIS, I can imagine that the Single Instance Storage Service might be a leading culprit.
The Single Instance Storage Groveler Service
Before going into the specifics on how to use RIS to deploy Windows 2000 Server, let's take a look at the Single Instance Storage Groveler Service. The purpose of this service is to reduce the amount of disk space consumed by multiple RIS images stored on a RIS partition/volume.
When you install the Remote Installation Service, you also install the Groveler. This service searches the partition/volume that contains your RIS images hoping to find duplicate files. When the Groveler finds duplicate files on the RIS partition/volume, it will place a single copy of the duplicate file in the SIS Common Store folder on that partition/volume. It then deletes the original files and creates a reparse point, which is a pointer to the actual file located in the SIS Common Store folder. Bet you didn't know that.
An interesting thing about the Groveler is that it isn't biased toward just RIS images. The Groveler searches the entire partition/volume for duplicates and creates the appropriate reparse points. This might be useful if you have multiple users downloading the same Star Wars trailer into their home directories. If you place the home directories on the volume that also contains the RIS images, the 200 instances of that 50 MB file go from taking up 10 Gigs on your hard disk to 50 MBs. Pretty nice, eh?
Of course, there are other considerations you should make before considering such a thing. But perhaps Microsoft will let you take advantage of this feature on non-RIS partitions in the future.
- Copy the contents of the i386 folder to a network share
or local hard disk. This is required because Txtsetup.sif file in that
folder must be modified.
- Using Notepad or any other text editor, open the Txtsetup.sif
file in the folder to which you copied the files in step 1.
- Locate the [SetupData] section in the file.
- Change the "ProductType" value from 1
to 0. Save the file and then quit the text editor.
- On the RIS server, run Risetup.exe and select
the option to add a new operating system image to the server. When the
program prompts you for the source files, point to the location of the
Windows 2000 Server files that you copied in step 1.
- When you are prompted for a directory name, Win2000.wks
may be the default name. Change this to Win2000.srv or another name
that you like more.
- Follow the rest of the instructions in Risetup.exe. When Risetup.exe is finished, open the Txtsetup.sif file in the folder you used in step 1, and change the "ProductType" value back to 1 and then save and close the file.
After making these adjustments, you'll be able to perform a network boot-up using either a Pre-boot Execution Environment (PXE) NIC or the RIS Boot Floppy. Just like you do when you install Windows 2000 Professional using RIS.
For More Information:
For more information on how to use RIS to install Windows 2000 Server, click HERE.
For the Knowledge Base article that contains these instructions click HERE.
For more information about the Groveler, click HERE.
For more information on RIS in general, check out Syngress/Osborne Study Guides HERE.
IT Solutions Builder TOP IT RESOURCES TO MOVE YOUR BUSINESS FORWARD
Which topic are you interested in?
What is your company size?
What is your job title?
What is your job function?
Searching our resource database to find your matches...